Hydro Jetting in Garfield Heights

Two eras of homes on a ridge above Mill Creek

Garfield Heights takes its name from the high ground south of the Cuyahoga valley, and its housing came in two pushes. The streets north of Garfield Boulevard and near Turney Road filled with bungalows and doubles in the 1920s. After the war, the colonials and ranches off Rockside Road, around Garfield Park, and toward the Maple Heights line went up through the 1950s. Both eras used vitrified clay laterals in short jointed lengths, with cast iron through the foundation and under the slab. Orangeburg shows up in some of the postwar blocks, and PVC is limited to a handful of newer streets and replacement laterals.

The lots along the Mill Creek ravine and the slopes near Garfield Park are steeper than most of the county, and the laterals there run downhill to a main that may be well below the house.

What breaks the lines here

The subsoil is glacial till with clay layers, which holds water on the flat ground and creeps slowly on the slopes. Clay joints on a hillside lateral tend to pull apart over the decades as the ground inches downhill, and the camera will show gaps rather than offsets. On the flatter streets the usual frost heave, down to about three feet, rocks the shallow run near the foundation every winter. Either way, the joints open, and the silver maples, pin oaks, and sycamores along the streets send roots in.

Garfield Heights has older sewers in its northern sections that carry storm water in a heavy rain, and leaky laterals across the city add groundwater to the sanitary system. When the main fills, sewage finds the lowest opening, which is usually a basement floor drain. The city has worked on separation and relief sewers, but basement backups remain a common reason for the first camera call.

Lining, bursting, or a spot repair

A clay lateral that is still round with roots and cracks is a lining job. The installer hydro jets the line, cuts the roots, inverts an epoxy-saturated felt liner from the basement cleanout, and cures it with hot water, steam, or UV. On a sloped lot, lining has the added advantage of no pits on the hillside. Once cured, the liner seals the joints and stops the groundwater that was feeding the backups.

If the camera finds a joint pulled fully apart, a crushed section, or an offset it cannot pass, pipe bursting is the method. A bursting head is pulled from a pit near the main to a pit at the house, breaking the clay while fused HDPE follows. Bursting pits on a slope need shoring and a plan for groundwater. A single cracked bell or one open joint in an otherwise sound line can be handled with a sectional point repair instead of a full liner.

Permits and the inspection in Garfield Heights

The city building department issues the sewer and plumbing permit. For lining, the inspector reviews the pre- and post-cure videos; for bursting, the inspector sees the new connection before the pits are filled. Any work in the tree lawn or street needs a right-of-way permit through the service department. Garfield Heights sewage is treated through the Northeast Ohio Regional Sewer District system, and the district's rules on storm water connections apply, which is why the inspector will ask whether downspouts, sump pumps, or footer drains are tied to the sanitary lateral.

In most communities the owner's responsibility runs to the main. On a ravine lot where the main sits far below, confirm the connection point with the city, since it affects how long the liner or the bursting pull must be.

On the day, and how to compare installers

A lining day begins with jetting and a camera pass, then the wet-out and inversion, a cure of a few hours, reinstatement of branch lines, and a final video. Drains are off until the cure is done. A bursting crew brings an excavator and shoring for the pits, a pulling rig, and comes back the next day to backfill, compact, and seed.

Ask every bidder to explain, from the footage, why they chose lining or bursting. Each scope should list the footage, the liner thickness or HDPE size, and the warranty. To compare installers whose training and insurance have been verified, find a verified CIPP contractor and request a reference from a sloped lot in Garfield Heights or a neighboring city. A crew that has shored a pit on a Mill Creek hillside will have a clear plan for yours.

Hydro Jetting in Garfield Heights

What a jetter does that a cable cannot

A hydro jetter pushes water through a nozzle at several thousand PSI. Rear-facing jets pull the hose down the line and scour everything off the pipe wall: roots, grease, sludge, mineral scale, and the rust flakes inside old cast iron. A cable machine drills a hole through the blockage and leaves the rest on the wall, which is why cabled lines re-clog on a schedule.

Where it fits in a repair

Jetting is step one before lining, because a liner has to bond to clean pipe, and step one before an honest camera inspection, because a line full of roots or scale hides its own condition. It is also legitimate maintenance on its own for a structurally sound line that roots keep finding.

When a line should not be jetted

Cast iron that is paper-thin at the bottom can be opened up by an aggressive descaling pass. A collapsed clay section will not let the hose through. Orangeburg can delaminate under pressure. An experienced operator checks the line first, matches the nozzle to the material, and stops if the pipe is not holding up.

Maintenance versus repair

If the camera shows sound pipe, annual or semiannual jetting is a cheap way to stay ahead of roots. If it shows open joints, channeled cast iron or offsets, jetting is a stopgap and the money is better spent on lining, which removes the joints the roots are using.

More trenchless services in Garfield Heights

Questions we hear in Garfield Heights